When was UniFi Network Application 10.6.106 released?

UniFi Network Application 10.6.106 was released on 2026-09-10.

Home › UniFi Network Application › 10.6.106

UniFi Network 10.6.106 – safe to update?

Q: Is UniFi Network Application 10.6.106 safe to update to?

Safe to update. 0 problem reports and 1 positive report found on Reddit (plus 11 other mentions). Out for 37 days with positive reports and no problem reports.

Safe to update

0 problem reports and 1 positive report found on Reddit (plus 11 other mentions). Out for 37 days with positive reports and no problem reports.

Requirements and changes

Lines from the official notes worth checking before you update:

Requires UAP 8.8 or newer.

Full release notes →

2026-09-10released

37days ago

0problem reports

1fine reports

0CVEs mapped

Did you install 10.6.106?

What's in this release

Improvements • Added MLO STR Mesh support for WiFi 7 Access Points. • Requires UAP 8.8 or newer. • Improved Application stability. • Improved Observability resiliency. Bugfixes • Fixed a rare issue where WiFi clients using MLO could display an incorrect IP address. • Fixed an issue where WiFi Broadcast could fail on U…

Official release notes →

Source: community.ui.com RSS

CVEs fixed

No CVEs mapped to this release.

Community reports

Fine UAP-Outdoor+ Still Adoptable · Reddit · 2026-10-12
My self hosted controller has been complaining about the UAP-Outdoor+ for a long time, so when I upgraded to a UDM-PRO and migrated my controller to it, I didn't expect it to work, and sure enough, it said the AP belonged to another controller and it couldn't adopt it. AP roamin…
Mention Is it possible to Revert the UCI's firmware from 1.43 to 1.36? I'm chasing a Spectrum issue. · Reddit · 2026-10-17
Running Network 10.6.106 from UCG Fiber. Backrev, or Revert, appears to be available for the UCI via its Control Plane page, but if launched it appears to work on it (small gas gauge) then fail with no notification. Ideas? Thanks!
Mention Update: repeated “HDD Removed” alerts on a UDM Pro · Reddit · 2026-10-16
Spoiler: it wasn't the disk and Ubiquiti RMA'ed the UDM Pro. A few months ago, I posted about a UDM Pro reporting “HDD Removed,” followed later by “Compatible HDD Installed” , despite nobody touching the disk at the client site. We’ve now investigated it on the bench, and Ubiqui…
Mention Severe throughput drop (~400 → ~16 Mbps) through UCG-Max only when iCloud Private Relay is enabled · Reddit · 2026-10-14
Hi all, For the second evening in a row I'm seeing a strange throughput issue, after almost a year of everything running smoothly. Setup: ISP modem in bridge mode, passing a public IP to the WAN interface of the UCG-Max UCG-Max connected to the ISP modem via the uplink port Clie…
Mention DHCP Guarding (and the trusted server IPs) wiped on all VLANs after a graceful shutdown. · Reddit · 2026-10-12
UCG-Fiber running Network 10.6.106 / UniFi OS 5.1.33 USW-Pro-HD-24-PoE, 4× U7 Pro XGS, six VLANs, each with DHCP Guarding enabled and the trusted server set to that VLAN’s gateway IP. Neighborhood power outage today. Everything was on a CyberPower CP1500PFCRM2U UPS, and when run…
Mention Policy Based Route Help Needed · Reddit · 2026-10-12
Edit: Solved thanks to u/That-Duck-7195 DNS Settings on Newtork: Old: 10.27.10.24 (pihole) Failed: 10.27.10.1 (VLAN gateway) Works: 10.27.5.1 (UCGF) It's the best of both worlds, since the pihole still logs the calling machine as the query source rather than the gateway. -------…
Mention UCG-Max slow download speeds with Hardware Acceleration enabled? · Reddit · 2026-10-08
Recently replaced my Xfinity xFi Gateway with an Arris S33 modem, UCG-Max, and U7 Lite. It’s frustrating to have worse performance than before. On my 1.2 Gbps plan, I was getting around 800 Mbps down using LibreSpeed CLI over a wired connection with a 1 GbE USB-C Ethernet dongle…
Mention Does ipv6 pbr through wireguard client work? · Reddit · 2026-10-07
I have unifi fiber gateway and unifi network 10.6.106 Wireguard VPN client connected to my VPs. A domain based policy sensitive traffic for domain through wireguard client. Ipv4 seem to work but ipv6 won't work. Is ipv6 pbr supported on unifi? Or only ipv4 works. I couldn't find…
Mention UCG-Fiber only getting 3.2–3.5 Gbps down, but 4.7 up. What am I missing? · Reddit · 2026-10-07
I'm on a 5 gig symmetrical plan. Plugging my PC straight into the ONT gets me around 4.7 Gbps both ways. With the UCG-Fiber in between, download drops to 3.2–3.5 Gbps while upload still hits 4.7. These are tests with the same wired PC, same Ookla Windows app, same server, and mu…
Mention AC Lite problems · Reddit · 2026-10-04
Currently on network 10.6.106 and am suddenly having problems with AC Lite access points spontaneously going off-line, then immediately recovering. We've a lot of other APs (u6 family and u7 family), and they're not misbehaving. Started today, as far as I can tell. Anyone else h…
Mention UDM Beast Storage Not Initialized · Reddit · 2026-10-01
I recently updated to an EA build (Unifi OS 6.0.10 / Network 10.6.106 if that matters) and noticed that my Control Plane / Storage was different. Instead of the standard "Install drives to use with Protect" or whatever it used to say, now it is telling me that the internal SSD n…
Mention Anyone Unable to Sign In With Webex Phone Services? · Reddit · 2026-10-01
Hi everyone. Strange issue I've been having for only a few months and I'm very curious if anyone else has seen this. I'm a network engineer for a company that is a Cisco partner, we use Webex for comms and have CUCM infra along with Webex Contact Center. My Webex apps are intend…

Reports are found automatically and labelled by an AI model plus keyword rules — they can be wrong. Open the post to judge for yourself.